[Apr 13, 2023] Passing Key To Getting NSE6_FWF-6.4 Certified Exam Engine PDF
NSE6_FWF-6.4 Exam Dumps Pass with Updated Apr-2023 Tests Dumps
NEW QUESTION 17
Refer to the exhibits.
Exhibit A
Exhibit B
Exhibit C
A wireless network has been installed in a small office building and is being used by a business to connect its wireless clients. The network is used for multiple purposes, including corporate access, guest access, and connecting point-of-sale and IoT devices.
Users connecting to the guest network located in the reception area are reporting slow performance. The network administrator is reviewing the information shown in the exhibits as part of the ongoing investigation of the problem. They show the profile used for the AP and the controller RF analysis output together with a screenshot of the GUI showing a summary of the AP and its neighboring APs.
To improve performance for the users connecting to the guest network in this area, which configuration change is most likely to improve performance?
- A. Reduce the number of wireless networks being broadcast by the AP
- B. Increase the transmission power of the AP radios
- C. Install another AP in the reception area to improve available bandwidth
- D. Enable frequency handoff on the AP to band steer clients
Answer: D
NEW QUESTION 18
Refer to the exhibit.
If the signal is set to -68 dB on the FortiPlanner site survey reading, which statement is correct regarding the coverage area?
- A. Areas with the signal strength weaker than -68 dB are highlighted in orange and red to indicate that no signal was propagated by the APs.
- B. Areas with the signal strength weaker than -68 dB are cut out of the map
- C. Areas with the signal strength equal or stronger than -68 dB are highlighted in multicolor
- D. Areas with the signal strength equal to -68 dB are zoomed in to provide better visibility
Answer: A
NEW QUESTION 19
Which two statements about distributed automatic radio resource provisioning (DARRP) are correct? (Choose two.)
- A. DARRP measurements can be scheduled to occur at specific times.
- B. DARRP performs continuous spectrum analysis to detect sources of interference. It uses this information to allow the AP to select the optimum channel.
- C. DARRP requires that wireless intrusion detection (WIDS) be enabled to detect neighboring devices.
- D. DARRP performs measurements of the number of BSSIDs and their signal strength (RSSI). The controller then uses this information to select the optimum channel for the AP.
Answer: A,D
Explanation:
According to Fortinet training: "When using DARRP, the AP selects the best channel available to use based on the scan results of BSSID/receive signal strength (RSSI) to AC" and "To set the running time for DARRP optimization, use the following CLI command within the wireless controller setting: set darrp-optimize {integer}. Note that DARRP doesn't do continuous spectrum analysis..."
NEW QUESTION 20
What type of design model does FortiPlanner use in wireless design project?
- A. Analytical model
- B. Architectural model
- C. Predictive model
- D. Integration model
Answer: B
Explanation:
FortiPlanner will look familiar to anyone who has used architectural or home design software.
NEW QUESTION 21
Where in the controller interface can you find a wireless client's upstream and downstream link rates?
- A. On the controller CLI, using the diag wireless-controller wlac -d sta command
- B. On the AP CLI, using the cw_diag ksta command
- C. On the controller CLI, using the WiFi Client monitor
- D. On the AP CLI, using the cw_diag -d sta command
Answer: B
NEW QUESTION 22
Which two statements about background rogue scanning are correct? (Choose two.)
- A. Background rogue scanning requires DARRP to be enabled on the AP instance
- B. A dedicated radio configured for background scanning can support the connection of wireless clients
- C. A dedicated radio configured for background scanning can detect rogue devices on all other channels in its configured frequency band
- D. When detecting rogue APs, a dedicated radio configured for background scanning can suppress the rogue AP
Answer: A,C
NEW QUESTION 23
Refer to the exhibits.
Exhibit A
Exhibit B
A wireless network has been created to support a group of users in a specific area of a building. The wireless network is configured but users are unable to connect to it. The exhibits show the relevant controller configuration for the APs and the wireless network.
Which two configuration changes will resolve the issue? (Choose two.)
- A. Disable intra-vap-privacy for the Authors vap-wireless network
- B. For both interfaces in the wtp-profile, configure set vaps to be "Authors"
- C. Increase the transmission power of the AP radio interfaces
- D. For both interfaces in the wtp-profile, configure vap-all to be manual
Answer: A,D
NEW QUESTION 24
Refer to the exhibit.
What does the asterisk (*) symbol beside the channel mean?
- A. Indicates channels that cannot be used because of regulatory channel restrictions
- B. Indicates channels that can be used only when Radio Resource Provisioning is enabled
- C. Indicates channels that will be scanned by the Wireless Intrusion Detection System (WIDS)
- D. Indicates channels that are subject to dynamic frequency selection (DFS) regulations
Answer: D
NEW QUESTION 25
You are investigating a wireless performance issue and you are trying to audit the neighboring APs in the PF environment. You review the Rogue APs widget on the GUI but it is empty, despite the known presence of other APs.
Which configuration change will allow neighboring APs to be successfully detected?
- A. Ensure that all allowed channels are enabled for the AP radios.
- B. Enable Locate WiFi clients when not connected in the relevant AP profiles.
- C. Enable Radio resource provisioning on the relevant AP profiles.
- D. Enable Monitor channel utilization on the relevant AP profiles.
Answer: C
Explanation:
The ARRP (Automatic Radio Resource Provisioning) profile improves upon DARRP (Distributed Automatic Radio Resource Provisioning) by allowing more factors to be considered to optimize channel selection among FortiAPs. DARRP uses the neighbor APs channels and signal strength collected from the background scan for channel selection.
NEW QUESTION 26
What type of design model does FortiPlanner use in wireless design project?
- A. Analytical model
- B. Predictive model
- C. Architectural model
- D. Integration model
Answer: B
NEW QUESTION 27
When enabling security fabric on the FortiGate interface to manage FortiAPs, which two types of communication channels are established between FortiGate and FortiAPs? (Choose two.)
- A. Security channels
- B. FortLink channels
- C. Data channels
- D. Control channels
Answer: C,D
Explanation:
The control channel for managing traffic, which is always encrypted by DTLS. l The data channel for carrying client data packets.
NEW QUESTION 28
Where in the controller interface can you find a wireless client's upstream and downstream link rates?
- A. On the controller CLI, using the WiFi Client monitor
- B. On the AP CLI, using the cw_diag ksta command
- C. On the controller CLI, using the diag wireless-controller wlac -d sta command
- D. On the AP CLI, using the cw_diag -d sta command
Answer: C
NEW QUESTION 29
Refer to the exhibit.
If the signal is set to -68 dB on the FortiPlanner site survey reading, which statement is correct regarding the coverage area?
- A. Areas with the signal strength weaker than -68 dB are highlighted in orange and red to indicate that no signal was propagated by the APs.
- B. Areas with the signal strength equal or stronger than -68 dB are highlighted in multicolor
- C. Areas with the signal strength weaker than -68 dB are cut out of the map
- D. Areas with the signal strength equal to -68 dB are zoomed in to provide better visibility
Answer: B
NEW QUESTION 30
Which statement describes FortiPresence location map functionality?
- A. Provides real-time insight into user usage stats
- B. Provides real-time insight into user movements
- C. Provides real-time insight into user online activity
- D. Provides real-time insight into user purchase activity
Answer: B
NEW QUESTION 31
Six APs are located in a remotely based branch office and are managed by a centrally hosted FortiGate. Multiple wireless users frequently connect and roam between the APs in the remote office.
The network they connect to, is secured with WPA2-PSK. As currently configured, the WAN connection between the branch office and the centrally hosted FortiGate is unreliable.
Which configuration would enable the most reliable wireless connectivity for the remote clients?
- A. Configure a tunnel mode wireless network and enable split tunneling to the local network
- B. Configure a bridge mode wireless network and enable the Local standalone configuration option
- C. Install supported FortiAP and configure a bridge mode wireless network
- D. Configure a bridge mode wireless network and enable the Local authentication configuration option
Answer: A
NEW QUESTION 32
Refer to the exhibits.
Exhibit A
Exhibit B
Exhibit C
A wireless network has been installed in a small office building and is being used by a business to connect its wireless clients. The network is used for multiple purposes, including corporate access, guest access, and connecting point-of-sale and IoT devices.
Users connecting to the guest network located in the reception area are reporting slow performance. The network administrator is reviewing the information shown in the exhibits as part of the ongoing investigation of the problem. They show the profile used for the AP and the controller RF analysis output together with a screenshot of the GUI showing a summary of the AP and its neighboring APs.
To improve performance for the users connecting to the guest network in this area, which configuration change is most likely to improve performance?
- A. Increase the transmission power of the AP radios
- B. Reduce the number of wireless networks being broadcast by the AP
- C. Install another AP in the reception area to improve available bandwidth
- D. Enable frequency handoff on the AP to band steer clients
Answer: A
NEW QUESTION 33
Which of the following is a requirement to generate analytic reports using on-site FortiPresence deployment?
- A. DTLS encryption on wireless traffic must be turned off
- B. Wireless network security must be set to open
- C. SQL services must be running
- D. Two wireless APs must be sending data
Answer: C
NEW QUESTION 34
Which factor is the best indicator of wireless client connection quality?
- A. The channel utilization of the channel the client is using
- B. Upstream link rate, the connection rate for the client to the AP
- C. Downstream link rate, the connection rate for the AP to the client
- D. The receive signal strength (RSS) of the client at the AP
Answer: B
NEW QUESTION 35
Refer to the exhibits.
Exhibit A
Exhibit B
The exhibits show the diagnose debug log of a station connection taken on the controller CLI.
Which security mode is used by the wireless connection?
- A. WPA3 Enterprise
- B. WPA2 Enterprise
- C. Open, with radius MAC filtering
- D. WPA2 Personal and radius MAC filtering
Answer: B
Explanation:
Best security option is WPA2-AES.
NEW QUESTION 36
......
NSE6_FWF-6.4 exam questions for practice in 2023 Updated 31 Questions: https://examtorrent.dumpsreview.com/NSE6_FWF-6.4-exam-dumps-review.html
